STM32F103xB HAL User Manual: stm32f1xx_hal

IWDG HAL module driver. This file provides firmware functions to manage the following functionalities of the Independent Watchdog (IWDG) peripheral: + Initialization and Start functions + IO operation functions. More...

#include "stm32f1xx_hal.h"

Go to the source code of this file.

Defines
#define	HAL_IWDG_DEFAULT_TIMEOUT (((6UL * 256UL * 1000UL) / LSI_VALUE) + ((LSI_STARTUP_TIME / 1000UL) + 1UL))
#define	IWDG_KERNEL_UPDATE_FLAGS (IWDG_SR_RVU \| IWDG_SR_PVU)
Functions
HAL_StatusTypeDef	HAL_IWDG_Init (IWDG_HandleTypeDef *hiwdg)
	Initialize the IWDG according to the specified parameters in the IWDG_InitTypeDef and start watchdog.
HAL_StatusTypeDef	HAL_IWDG_Refresh (IWDG_HandleTypeDef *hiwdg)
	Refresh the IWDG.

Detailed Description

Author:

MCD Application Team

  ==============================================================================
                    ##### IWDG Generic features #####
  ==============================================================================
  [..]
    (+) The IWDG can be started by either software or hardware (configurable
        through option byte).

    (+) The IWDG is clocked by the Low-Speed Internal clock (LSI) and thus stays
        active even if the main clock fails.

    (+) Once the IWDG is started, the LSI is forced ON and both cannot be
        disabled. The counter starts counting down from the reset value (0xFFF).
        When it reaches the end of count value (0x000) a reset signal is
        generated (IWDG reset).

    (+) Whenever the key value 0x0000 AAAA is written in the IWDG_KR register,
        the IWDG_RLR value is reloaded into the counter and the watchdog reset
        is prevented.

    (+) The IWDG is implemented in the VDD voltage domain that is still functional
        in STOP and STANDBY mode (IWDG reset can wake up the CPU from STANDBY).
        IWDGRST flag in RCC_CSR register can be used to inform when an IWDG
        reset occurs.

    (+) Debug mode: When the microcontroller enters debug mode (core halted),
        the IWDG counter either continues to work normally or stops, depending
        on DBG_IWDG_STOP configuration bit in DBG module, accessible through
        __HAL_DBGMCU_FREEZE_IWDG() and __HAL_DBGMCU_UNFREEZE_IWDG() macros.

    [..] Min-max timeout value @32KHz (LSI): ~125us / ~32.7s
         The IWDG timeout may vary due to LSI clock frequency dispersion.
         STM32F1xx devices provide the capability to measure the LSI clock
         frequency (LSI clock is internally connected to TIM5 CH4 input capture).
         The measured value can be used to have an IWDG timeout with an
         acceptable accuracy.

    [..] Default timeout value (necessary for IWDG_SR status register update):
         Constant LSI_VALUE is defined based on the nominal LSI clock frequency.
         This frequency being subject to variations as mentioned above, the
         default timeout value (defined through constant HAL_IWDG_DEFAULT_TIMEOUT
         below) may become too short or too long.
         In such cases, this default timeout value can be tuned by redefining
         the constant LSI_VALUE at user-application level (based, for instance,
         on the measured LSI clock frequency as explained above).

                     ##### How to use this driver #####
  ==============================================================================
  [..]
    (#) Use IWDG using HAL_IWDG_Init() function to :
      (++) Enable instance by writing Start keyword in IWDG_KEY register. LSI
           clock is forced ON and IWDG counter starts counting down.
      (++) Enable write access to configuration registers:
          IWDG_PR and IWDG_RLR.
      (++) Configure the IWDG prescaler and counter reload value. This reload
           value will be loaded in the IWDG counter each time the watchdog is
           reloaded, then the IWDG will start counting down from this value.
      (++) Wait for status flags to be reset.

    (#) Then the application program must refresh the IWDG counter at regular
        intervals during normal operation to prevent an MCU reset, using
        HAL_IWDG_Refresh() function.

     *** IWDG HAL driver macros list ***
     ====================================
     [..]
       Below the list of most used macros in IWDG HAL driver:
      (+) __HAL_IWDG_START: Enable the IWDG peripheral
      (+) __HAL_IWDG_RELOAD_COUNTER: Reloads IWDG counter with value defined in
          the reload register

Attention:

This software component is licensed by ST under BSD 3-Clause license, the "License"; You may not use this file except in compliance with the License. You may obtain a copy of the License at: opensource.org/licenses/BSD-3-Clause

Definition in file stm32f1xx_hal_iwdg.c.

Defines

Functions

Detailed Description

© Copyright (c) 2016 STMicroelectronics. All rights reserved.