|
STM32F479xx HAL User Manual
|
00001 /** 00002 ****************************************************************************** 00003 * @file stm32f4xx_hal_conf_template.h 00004 * @author MCD Application Team 00005 * @brief HAL configuration template file. 00006 * This file should be copied to the application folder and renamed 00007 * to stm32f4xx_hal_conf.h. 00008 ****************************************************************************** 00009 * @attention 00010 * 00011 * <h2><center>© Copyright (c) 2017 STMicroelectronics. 00012 * All rights reserved.</center></h2> 00013 * 00014 * This software component is licensed by ST under BSD 3-Clause license, 00015 * the "License"; You may not use this file except in compliance with the 00016 * License. You may obtain a copy of the License at: 00017 * opensource.org/licenses/BSD-3-Clause 00018 * 00019 ****************************************************************************** 00020 */ 00021 00022 /* Define to prevent recursive inclusion -------------------------------------*/ 00023 #ifndef __STM32F4xx_HAL_CONF_H 00024 #define __STM32F4xx_HAL_CONF_H 00025 00026 #ifdef __cplusplus 00027 extern "C" { 00028 #endif 00029 00030 /* Exported types ------------------------------------------------------------*/ 00031 /* Exported constants --------------------------------------------------------*/ 00032 00033 /* ########################## Module Selection ############################## */ 00034 /** 00035 * @brief This is the list of modules to be used in the HAL driver 00036 */ 00037 #define HAL_MODULE_ENABLED 00038 #define HAL_ADC_MODULE_ENABLED 00039 #define HAL_CAN_MODULE_ENABLED 00040 /* #define HAL_CAN_LEGACY_MODULE_ENABLED */ 00041 #define HAL_CRC_MODULE_ENABLED 00042 #define HAL_CEC_MODULE_ENABLED 00043 #define HAL_CRYP_MODULE_ENABLED 00044 #define HAL_DAC_MODULE_ENABLED 00045 #define HAL_DCMI_MODULE_ENABLED 00046 #define HAL_DMA_MODULE_ENABLED 00047 #define HAL_DMA2D_MODULE_ENABLED 00048 #define HAL_ETH_MODULE_ENABLED 00049 #define HAL_FLASH_MODULE_ENABLED 00050 #define HAL_NAND_MODULE_ENABLED 00051 #define HAL_NOR_MODULE_ENABLED 00052 #define HAL_PCCARD_MODULE_ENABLED 00053 #define HAL_SRAM_MODULE_ENABLED 00054 #define HAL_SDRAM_MODULE_ENABLED 00055 #define HAL_HASH_MODULE_ENABLED 00056 #define HAL_GPIO_MODULE_ENABLED 00057 #define HAL_EXTI_MODULE_ENABLED 00058 #define HAL_I2C_MODULE_ENABLED 00059 #define HAL_SMBUS_MODULE_ENABLED 00060 #define HAL_I2S_MODULE_ENABLED 00061 #define HAL_IWDG_MODULE_ENABLED 00062 #define HAL_LTDC_MODULE_ENABLED 00063 #define HAL_DSI_MODULE_ENABLED 00064 #define HAL_PWR_MODULE_ENABLED 00065 #define HAL_QSPI_MODULE_ENABLED 00066 #define HAL_RCC_MODULE_ENABLED 00067 #define HAL_RNG_MODULE_ENABLED 00068 #define HAL_RTC_MODULE_ENABLED 00069 #define HAL_SAI_MODULE_ENABLED 00070 #define HAL_SD_MODULE_ENABLED 00071 #define HAL_SPI_MODULE_ENABLED 00072 #define HAL_TIM_MODULE_ENABLED 00073 #define HAL_UART_MODULE_ENABLED 00074 #define HAL_USART_MODULE_ENABLED 00075 #define HAL_IRDA_MODULE_ENABLED 00076 #define HAL_SMARTCARD_MODULE_ENABLED 00077 #define HAL_WWDG_MODULE_ENABLED 00078 #define HAL_CORTEX_MODULE_ENABLED 00079 #define HAL_PCD_MODULE_ENABLED 00080 #define HAL_HCD_MODULE_ENABLED 00081 #define HAL_FMPI2C_MODULE_ENABLED 00082 #define HAL_FMPSMBUS_MODULE_ENABLED 00083 #define HAL_SPDIFRX_MODULE_ENABLED 00084 #define HAL_DFSDM_MODULE_ENABLED 00085 #define HAL_LPTIM_MODULE_ENABLED 00086 #define HAL_MMC_MODULE_ENABLED 00087 00088 /* ########################## HSE/HSI Values adaptation ##################### */ 00089 /** 00090 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 00091 * This value is used by the RCC HAL module to compute the system frequency 00092 * (when HSE is used as system clock source, directly or through the PLL). 00093 */ 00094 #if !defined (HSE_VALUE) 00095 #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ 00096 #endif /* HSE_VALUE */ 00097 00098 #if !defined (HSE_STARTUP_TIMEOUT) 00099 #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ 00100 #endif /* HSE_STARTUP_TIMEOUT */ 00101 00102 /** 00103 * @brief Internal High Speed oscillator (HSI) value. 00104 * This value is used by the RCC HAL module to compute the system frequency 00105 * (when HSI is used as system clock source, directly or through the PLL). 00106 */ 00107 #if !defined (HSI_VALUE) 00108 #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ 00109 #endif /* HSI_VALUE */ 00110 00111 /** 00112 * @brief Internal Low Speed oscillator (LSI) value. 00113 */ 00114 #if !defined (LSI_VALUE) 00115 #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ 00116 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 00117 The real value may vary depending on the variations 00118 in voltage and temperature. */ 00119 /** 00120 * @brief External Low Speed oscillator (LSE) value. 00121 */ 00122 #if !defined (LSE_VALUE) 00123 #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ 00124 #endif /* LSE_VALUE */ 00125 00126 #if !defined (LSE_STARTUP_TIMEOUT) 00127 #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ 00128 #endif /* LSE_STARTUP_TIMEOUT */ 00129 00130 /** 00131 * @brief External clock source for I2S peripheral 00132 * This value is used by the I2S HAL module to compute the I2S clock source 00133 * frequency, this source is inserted directly through I2S_CKIN pad. 00134 */ 00135 #if !defined (EXTERNAL_CLOCK_VALUE) 00136 #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ 00137 #endif /* EXTERNAL_CLOCK_VALUE */ 00138 00139 /* Tip: To avoid modifying this file each time you need to use different HSE, 00140 === you can define the HSE value in your toolchain compiler preprocessor. */ 00141 00142 /* ########################### System Configuration ######################### */ 00143 /** 00144 * @brief This is the HAL system configuration section 00145 */ 00146 #define VDD_VALUE 3300U /*!< Value of VDD in mv */ 00147 #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ 00148 #define USE_RTOS 0U 00149 #define PREFETCH_ENABLE 1U 00150 #define INSTRUCTION_CACHE_ENABLE 1U 00151 #define DATA_CACHE_ENABLE 1U 00152 00153 #define USE_HAL_ADC_REGISTER_CALLBACKS 1U /* ADC register callback disabled */ 00154 #define USE_HAL_CAN_REGISTER_CALLBACKS 1U /* CAN register callback disabled */ 00155 #define USE_HAL_CEC_REGISTER_CALLBACKS 1U /* CEC register callback disabled */ 00156 #define USE_HAL_CRYP_REGISTER_CALLBACKS 1U /* CRYP register callback disabled */ 00157 #define USE_HAL_DAC_REGISTER_CALLBACKS 1U /* DAC register callback disabled */ 00158 #define USE_HAL_DCMI_REGISTER_CALLBACKS 1U /* DCMI register callback disabled */ 00159 #define USE_HAL_DFSDM_REGISTER_CALLBACKS 1U /* DFSDM register callback disabled */ 00160 #define USE_HAL_DMA2D_REGISTER_CALLBACKS 1U /* DMA2D register callback disabled */ 00161 #define USE_HAL_DSI_REGISTER_CALLBACKS 1U /* DSI register callback disabled */ 00162 #define USE_HAL_ETH_REGISTER_CALLBACKS 1U /* ETH register callback disabled */ 00163 #define USE_HAL_HASH_REGISTER_CALLBACKS 1U /* HASH register callback disabled */ 00164 #define USE_HAL_HCD_REGISTER_CALLBACKS 1U /* HCD register callback disabled */ 00165 #define USE_HAL_I2C_REGISTER_CALLBACKS 1U /* I2C register callback disabled */ 00166 #define USE_HAL_FMPI2C_REGISTER_CALLBACKS 1U /* FMPI2C register callback disabled */ 00167 #define USE_HAL_FMPSMBUS_REGISTER_CALLBACKS 1U /* FMPSMBUS register callback disabled */ 00168 #define USE_HAL_I2S_REGISTER_CALLBACKS 1U /* I2S register callback disabled */ 00169 #define USE_HAL_IRDA_REGISTER_CALLBACKS 1U /* IRDA register callback disabled */ 00170 #define USE_HAL_LPTIM_REGISTER_CALLBACKS 1U /* LPTIM register callback disabled */ 00171 #define USE_HAL_LTDC_REGISTER_CALLBACKS 1U /* LTDC register callback disabled */ 00172 #define USE_HAL_MMC_REGISTER_CALLBACKS 1U /* MMC register callback disabled */ 00173 #define USE_HAL_NAND_REGISTER_CALLBACKS 1U /* NAND register callback disabled */ 00174 #define USE_HAL_NOR_REGISTER_CALLBACKS 1U /* NOR register callback disabled */ 00175 #define USE_HAL_PCCARD_REGISTER_CALLBACKS 1U /* PCCARD register callback disabled */ 00176 #define USE_HAL_PCD_REGISTER_CALLBACKS 1U /* PCD register callback disabled */ 00177 #define USE_HAL_QSPI_REGISTER_CALLBACKS 1U /* QSPI register callback disabled */ 00178 #define USE_HAL_RNG_REGISTER_CALLBACKS 1U /* RNG register callback disabled */ 00179 #define USE_HAL_RTC_REGISTER_CALLBACKS 1U /* RTC register callback disabled */ 00180 #define USE_HAL_SAI_REGISTER_CALLBACKS 1U /* SAI register callback disabled */ 00181 #define USE_HAL_SD_REGISTER_CALLBACKS 1U /* SD register callback disabled */ 00182 #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 1U /* SMARTCARD register callback disabled */ 00183 #define USE_HAL_SDRAM_REGISTER_CALLBACKS 1U /* SDRAM register callback disabled */ 00184 #define USE_HAL_SRAM_REGISTER_CALLBACKS 1U /* SRAM register callback disabled */ 00185 #define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 1U /* SPDIFRX register callback disabled */ 00186 #define USE_HAL_SMBUS_REGISTER_CALLBACKS 1U /* SMBUS register callback disabled */ 00187 #define USE_HAL_SPI_REGISTER_CALLBACKS 1U /* SPI register callback disabled */ 00188 #define USE_HAL_TIM_REGISTER_CALLBACKS 1U /* TIM register callback disabled */ 00189 #define USE_HAL_UART_REGISTER_CALLBACKS 1U /* UART register callback disabled */ 00190 #define USE_HAL_USART_REGISTER_CALLBACKS 1U /* USART register callback disabled */ 00191 #define USE_HAL_WWDG_REGISTER_CALLBACKS 1U /* WWDG register callback disabled */ 00192 00193 /* ########################## Assert Selection ############################## */ 00194 /** 00195 * @brief Uncomment the line below to expanse the "assert_param" macro in the 00196 * HAL drivers code 00197 */ 00198 /* #define USE_FULL_ASSERT 1U */ 00199 00200 /* ################## Ethernet peripheral configuration ##################### */ 00201 00202 /* Section 1 : Ethernet peripheral configuration */ 00203 00204 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 00205 #define MAC_ADDR0 2U 00206 #define MAC_ADDR1 0U 00207 #define MAC_ADDR2 0U 00208 #define MAC_ADDR3 0U 00209 #define MAC_ADDR4 0U 00210 #define MAC_ADDR5 0U 00211 00212 /* Definition of the Ethernet driver buffers size and count */ 00213 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 00214 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 00215 #define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 00216 #define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 00217 00218 /* Section 2: PHY configuration section */ 00219 00220 /* DP83848 PHY Address*/ 00221 #define DP83848_PHY_ADDRESS 0x01U 00222 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 00223 #define PHY_RESET_DELAY 0x000000FFU 00224 /* PHY Configuration delay */ 00225 #define PHY_CONFIG_DELAY 0x00000FFFU 00226 00227 #define PHY_READ_TO 0x0000FFFFU 00228 #define PHY_WRITE_TO 0x0000FFFFU 00229 00230 /* Section 3: Common PHY Registers */ 00231 00232 #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ 00233 #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ 00234 00235 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ 00236 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ 00237 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ 00238 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ 00239 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ 00240 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ 00241 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ 00242 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ 00243 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ 00244 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ 00245 00246 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ 00247 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ 00248 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ 00249 00250 /* Section 4: Extended PHY Registers */ 00251 00252 #define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ 00253 #define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ 00254 #define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ 00255 00256 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ 00257 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ 00258 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ 00259 00260 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ 00261 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ 00262 00263 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ 00264 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ 00265 00266 /* ################## SPI peripheral configuration ########################## */ 00267 00268 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 00269 * Activated: CRC code is present inside driver 00270 * Deactivated: CRC code cleaned from driver 00271 */ 00272 00273 #define USE_SPI_CRC 1U 00274 00275 /* Includes ------------------------------------------------------------------*/ 00276 /** 00277 * @brief Include module's header file 00278 */ 00279 00280 #ifdef HAL_RCC_MODULE_ENABLED 00281 #include "stm32f4xx_hal_rcc.h" 00282 #endif /* HAL_RCC_MODULE_ENABLED */ 00283 00284 #ifdef HAL_GPIO_MODULE_ENABLED 00285 #include "stm32f4xx_hal_gpio.h" 00286 #endif /* HAL_GPIO_MODULE_ENABLED */ 00287 00288 #ifdef HAL_EXTI_MODULE_ENABLED 00289 #include "stm32f4xx_hal_exti.h" 00290 #endif /* HAL_EXTI_MODULE_ENABLED */ 00291 00292 #ifdef HAL_DMA_MODULE_ENABLED 00293 #include "stm32f4xx_hal_dma.h" 00294 #endif /* HAL_DMA_MODULE_ENABLED */ 00295 00296 #ifdef HAL_CORTEX_MODULE_ENABLED 00297 #include "stm32f4xx_hal_cortex.h" 00298 #endif /* HAL_CORTEX_MODULE_ENABLED */ 00299 00300 #ifdef HAL_ADC_MODULE_ENABLED 00301 #include "stm32f4xx_hal_adc.h" 00302 #endif /* HAL_ADC_MODULE_ENABLED */ 00303 00304 #ifdef HAL_CAN_MODULE_ENABLED 00305 #include "stm32f4xx_hal_can.h" 00306 #endif /* HAL_CAN_MODULE_ENABLED */ 00307 00308 #ifdef HAL_CAN_LEGACY_MODULE_ENABLED 00309 #include "stm32f4xx_hal_can_legacy.h" 00310 #endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ 00311 00312 #ifdef HAL_CRC_MODULE_ENABLED 00313 #include "stm32f4xx_hal_crc.h" 00314 #endif /* HAL_CRC_MODULE_ENABLED */ 00315 00316 #ifdef HAL_CRYP_MODULE_ENABLED 00317 #include "stm32f4xx_hal_cryp.h" 00318 #endif /* HAL_CRYP_MODULE_ENABLED */ 00319 00320 #ifdef HAL_DMA2D_MODULE_ENABLED 00321 #include "stm32f4xx_hal_dma2d.h" 00322 #endif /* HAL_DMA2D_MODULE_ENABLED */ 00323 00324 #ifdef HAL_DAC_MODULE_ENABLED 00325 #include "stm32f4xx_hal_dac.h" 00326 #endif /* HAL_DAC_MODULE_ENABLED */ 00327 00328 #ifdef HAL_DCMI_MODULE_ENABLED 00329 #include "stm32f4xx_hal_dcmi.h" 00330 #endif /* HAL_DCMI_MODULE_ENABLED */ 00331 00332 #ifdef HAL_ETH_MODULE_ENABLED 00333 #include "stm32f4xx_hal_eth.h" 00334 #endif /* HAL_ETH_MODULE_ENABLED */ 00335 00336 #ifdef HAL_FLASH_MODULE_ENABLED 00337 #include "stm32f4xx_hal_flash.h" 00338 #endif /* HAL_FLASH_MODULE_ENABLED */ 00339 00340 #ifdef HAL_SRAM_MODULE_ENABLED 00341 #include "stm32f4xx_hal_sram.h" 00342 #endif /* HAL_SRAM_MODULE_ENABLED */ 00343 00344 #ifdef HAL_NOR_MODULE_ENABLED 00345 #include "stm32f4xx_hal_nor.h" 00346 #endif /* HAL_NOR_MODULE_ENABLED */ 00347 00348 #ifdef HAL_NAND_MODULE_ENABLED 00349 #include "stm32f4xx_hal_nand.h" 00350 #endif /* HAL_NAND_MODULE_ENABLED */ 00351 00352 #ifdef HAL_PCCARD_MODULE_ENABLED 00353 #include "stm32f4xx_hal_pccard.h" 00354 #endif /* HAL_PCCARD_MODULE_ENABLED */ 00355 00356 #ifdef HAL_SDRAM_MODULE_ENABLED 00357 #include "stm32f4xx_hal_sdram.h" 00358 #endif /* HAL_SDRAM_MODULE_ENABLED */ 00359 00360 #ifdef HAL_HASH_MODULE_ENABLED 00361 #include "stm32f4xx_hal_hash.h" 00362 #endif /* HAL_HASH_MODULE_ENABLED */ 00363 00364 #ifdef HAL_I2C_MODULE_ENABLED 00365 #include "stm32f4xx_hal_i2c.h" 00366 #endif /* HAL_I2C_MODULE_ENABLED */ 00367 00368 #ifdef HAL_SMBUS_MODULE_ENABLED 00369 #include "stm32f4xx_hal_smbus.h" 00370 #endif /* HAL_SMBUS_MODULE_ENABLED */ 00371 00372 #ifdef HAL_I2S_MODULE_ENABLED 00373 #include "stm32f4xx_hal_i2s.h" 00374 #endif /* HAL_I2S_MODULE_ENABLED */ 00375 00376 #ifdef HAL_IWDG_MODULE_ENABLED 00377 #include "stm32f4xx_hal_iwdg.h" 00378 #endif /* HAL_IWDG_MODULE_ENABLED */ 00379 00380 #ifdef HAL_LTDC_MODULE_ENABLED 00381 #include "stm32f4xx_hal_ltdc.h" 00382 #endif /* HAL_LTDC_MODULE_ENABLED */ 00383 00384 #ifdef HAL_PWR_MODULE_ENABLED 00385 #include "stm32f4xx_hal_pwr.h" 00386 #endif /* HAL_PWR_MODULE_ENABLED */ 00387 00388 #ifdef HAL_RNG_MODULE_ENABLED 00389 #include "stm32f4xx_hal_rng.h" 00390 #endif /* HAL_RNG_MODULE_ENABLED */ 00391 00392 #ifdef HAL_RTC_MODULE_ENABLED 00393 #include "stm32f4xx_hal_rtc.h" 00394 #endif /* HAL_RTC_MODULE_ENABLED */ 00395 00396 #ifdef HAL_SAI_MODULE_ENABLED 00397 #include "stm32f4xx_hal_sai.h" 00398 #endif /* HAL_SAI_MODULE_ENABLED */ 00399 00400 #ifdef HAL_SD_MODULE_ENABLED 00401 #include "stm32f4xx_hal_sd.h" 00402 #endif /* HAL_SD_MODULE_ENABLED */ 00403 00404 #ifdef HAL_SPI_MODULE_ENABLED 00405 #include "stm32f4xx_hal_spi.h" 00406 #endif /* HAL_SPI_MODULE_ENABLED */ 00407 00408 #ifdef HAL_TIM_MODULE_ENABLED 00409 #include "stm32f4xx_hal_tim.h" 00410 #endif /* HAL_TIM_MODULE_ENABLED */ 00411 00412 #ifdef HAL_UART_MODULE_ENABLED 00413 #include "stm32f4xx_hal_uart.h" 00414 #endif /* HAL_UART_MODULE_ENABLED */ 00415 00416 #ifdef HAL_USART_MODULE_ENABLED 00417 #include "stm32f4xx_hal_usart.h" 00418 #endif /* HAL_USART_MODULE_ENABLED */ 00419 00420 #ifdef HAL_IRDA_MODULE_ENABLED 00421 #include "stm32f4xx_hal_irda.h" 00422 #endif /* HAL_IRDA_MODULE_ENABLED */ 00423 00424 #ifdef HAL_SMARTCARD_MODULE_ENABLED 00425 #include "stm32f4xx_hal_smartcard.h" 00426 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 00427 00428 #ifdef HAL_WWDG_MODULE_ENABLED 00429 #include "stm32f4xx_hal_wwdg.h" 00430 #endif /* HAL_WWDG_MODULE_ENABLED */ 00431 00432 #ifdef HAL_PCD_MODULE_ENABLED 00433 #include "stm32f4xx_hal_pcd.h" 00434 #endif /* HAL_PCD_MODULE_ENABLED */ 00435 00436 #ifdef HAL_HCD_MODULE_ENABLED 00437 #include "stm32f4xx_hal_hcd.h" 00438 #endif /* HAL_HCD_MODULE_ENABLED */ 00439 00440 #ifdef HAL_DSI_MODULE_ENABLED 00441 #include "stm32f4xx_hal_dsi.h" 00442 #endif /* HAL_DSI_MODULE_ENABLED */ 00443 00444 #ifdef HAL_QSPI_MODULE_ENABLED 00445 #include "stm32f4xx_hal_qspi.h" 00446 #endif /* HAL_QSPI_MODULE_ENABLED */ 00447 00448 #ifdef HAL_CEC_MODULE_ENABLED 00449 #include "stm32f4xx_hal_cec.h" 00450 #endif /* HAL_CEC_MODULE_ENABLED */ 00451 00452 #ifdef HAL_FMPI2C_MODULE_ENABLED 00453 #include "stm32f4xx_hal_fmpi2c.h" 00454 #endif /* HAL_FMPI2C_MODULE_ENABLED */ 00455 00456 #ifdef HAL_FMPSMBUS_MODULE_ENABLED 00457 #include "stm32f4xx_hal_fmpsmbus.h" 00458 #endif /* HAL_FMPSMBUS_MODULE_ENABLED */ 00459 00460 #ifdef HAL_SPDIFRX_MODULE_ENABLED 00461 #include "stm32f4xx_hal_spdifrx.h" 00462 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 00463 00464 #ifdef HAL_DFSDM_MODULE_ENABLED 00465 #include "stm32f4xx_hal_dfsdm.h" 00466 #endif /* HAL_DFSDM_MODULE_ENABLED */ 00467 00468 #ifdef HAL_LPTIM_MODULE_ENABLED 00469 #include "stm32f4xx_hal_lptim.h" 00470 #endif /* HAL_LPTIM_MODULE_ENABLED */ 00471 00472 #ifdef HAL_MMC_MODULE_ENABLED 00473 #include "stm32f4xx_hal_mmc.h" 00474 #endif /* HAL_MMC_MODULE_ENABLED */ 00475 00476 /* Exported macro ------------------------------------------------------------*/ 00477 #ifdef USE_FULL_ASSERT 00478 /** 00479 * @brief The assert_param macro is used for function's parameters check. 00480 * @param expr If expr is false, it calls assert_failed function 00481 * which reports the name of the source file and the source 00482 * line number of the call that failed. 00483 * If expr is true, it returns no value. 00484 * @retval None 00485 */ 00486 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 00487 /* Exported functions ------------------------------------------------------- */ 00488 void assert_failed(uint8_t* file, uint32_t line); 00489 #else 00490 #define assert_param(expr) ((void)0U) 00491 #endif /* USE_FULL_ASSERT */ 00492 00493 00494 #ifdef __cplusplus 00495 } 00496 #endif 00497 00498 #endif /* __STM32F4xx_HAL_CONF_H */ 00499 00500 00501 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
1.7.6.1