SMBUS Exported Macros

Defines
#define	__HAL_SMBUS_RESET_HANDLE_STATE(__HANDLE__)
	Reset SMBUS handle state.
#define	__HAL_SMBUS_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((__HANDLE__)->Instance->CR1 |= (__INTERRUPT__))
	Enable the specified SMBUS interrupts.
#define	__HAL_SMBUS_DISABLE_IT(__HANDLE__, __INTERRUPT__)   ((__HANDLE__)->Instance->CR1 &= (~(__INTERRUPT__)))
	Disable the specified SMBUS interrupts.
#define	__HAL_SMBUS_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)   ((((__HANDLE__)->Instance->CR1 & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
	Check whether the specified SMBUS interrupt source is enabled or not.
#define	SMBUS_FLAG_MASK   (0x0001FFFFU)
	Check whether the specified SMBUS flag is set or not.
#define	__HAL_SMBUS_GET_FLAG(__HANDLE__, __FLAG__)
#define	__HAL_SMBUS_CLEAR_FLAG(__HANDLE__, __FLAG__)
	Clear the SMBUS pending flags which are cleared by writing 1 in a specific bit.
#define	__HAL_SMBUS_ENABLE(__HANDLE__)   (SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
	Enable the specified SMBUS peripheral.
#define	__HAL_SMBUS_DISABLE(__HANDLE__)   (CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
	Disable the specified SMBUS peripheral.
#define	__HAL_SMBUS_GENERATE_NACK(__HANDLE__)   (SET_BIT((__HANDLE__)->Instance->CR2, I2C_CR2_NACK))
	Generate a Non-Acknowledge SMBUS peripheral in Slave mode.

---

Define Documentation

#define __HAL_SMBUS_CLEAR_FLAG	(		__HANDLE__,
			__FLAG__
	)

Value:

(((__FLAG__) == SMBUS_FLAG_TXE) ? \
                                                       ((__HANDLE__)->Instance->ISR |= (__FLAG__)) : \
                                                       ((__HANDLE__)->Instance->ICR = (__FLAG__)))

Clear the SMBUS pending flags which are cleared by writing 1 in a specific bit.

Parameters:

__HANDLE__

specifies the SMBUS Handle.

__FLAG__

specifies the flag to clear. This parameter can be any combination of the following values: SMBUS_FLAG_TXE Transmit data register empty SMBUS_FLAG_ADDR Address matched (slave mode) SMBUS_FLAG_AF NACK received flag SMBUS_FLAG_STOPF STOP detection flag SMBUS_FLAG_BERR Bus error SMBUS_FLAG_ARLO Arbitration lost SMBUS_FLAG_OVR Overrun/Underrun SMBUS_FLAG_PECERR PEC error in reception SMBUS_FLAG_TIMEOUT Timeout or Tlow detection flag SMBUS_FLAG_ALERT SMBus alert

Return values:

None

Definition at line 527 of file stm32l4xx_hal_smbus.h.

Referenced by HAL_SMBUS_EnableAlert_IT(), HAL_SMBUS_IsDeviceReady(), HAL_SMBUS_Slave_Receive_IT(), HAL_SMBUS_Slave_Transmit_IT(), SMBUS_Flush_TXDR(), SMBUS_ITErrorHandler(), SMBUS_Master_ISR(), and SMBUS_Slave_ISR().

#define __HAL_SMBUS_DISABLE

(

__HANDLE__

)

(CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))

Disable the specified SMBUS peripheral.

Parameters:

__HANDLE__

specifies the SMBUS Handle.

Return values:

None

Definition at line 541 of file stm32l4xx_hal_smbus.h.

Referenced by HAL_SMBUS_ConfigAnalogFilter(), HAL_SMBUS_ConfigDigitalFilter(), HAL_SMBUS_DeInit(), HAL_SMBUS_Init(), HAL_SMBUSEx_DisableWakeUp(), HAL_SMBUSEx_EnableWakeUp(), and SMBUS_Master_ISR().

#define __HAL_SMBUS_DISABLE_IT	(		__HANDLE__,
			__INTERRUPT__
	)		((__HANDLE__)->Instance->CR1 &= (~(__INTERRUPT__)))

Disable the specified SMBUS interrupts.

Parameters:

__HANDLE__	specifies the SMBUS Handle.
__INTERRUPT__	specifies the interrupt source to disable. This parameter can be one of the following values: SMBUS_IT_ERRI Errors interrupt enable SMBUS_IT_TCI Transfer complete interrupt enable SMBUS_IT_STOPI STOP detection interrupt enable SMBUS_IT_NACKI NACK received interrupt enable SMBUS_IT_ADDRI Address match interrupt enable SMBUS_IT_RXI RX interrupt enable SMBUS_IT_TXI TX interrupt enable

Return values:

None

Definition at line 463 of file stm32l4xx_hal_smbus.h.

Referenced by SMBUS_Disable_IRQ(), and SMBUS_Slave_ISR().

#define __HAL_SMBUS_ENABLE

(

__HANDLE__

)

(SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))

Enable the specified SMBUS peripheral.

Parameters:

__HANDLE__

specifies the SMBUS Handle.

Return values:

None

Definition at line 535 of file stm32l4xx_hal_smbus.h.

Referenced by HAL_SMBUS_ConfigAnalogFilter(), HAL_SMBUS_ConfigDigitalFilter(), HAL_SMBUS_Init(), HAL_SMBUSEx_DisableWakeUp(), HAL_SMBUSEx_EnableWakeUp(), and SMBUS_Master_ISR().

#define __HAL_SMBUS_ENABLE_IT	(		__HANDLE__,
			__INTERRUPT__
	)		((__HANDLE__)->Instance->CR1 |= (__INTERRUPT__))

Enable the specified SMBUS interrupts.

Parameters:

__HANDLE__	specifies the SMBUS Handle.
__INTERRUPT__	specifies the interrupt source to enable. This parameter can be one of the following values: SMBUS_IT_ERRI Errors interrupt enable SMBUS_IT_TCI Transfer complete interrupt enable SMBUS_IT_STOPI STOP detection interrupt enable SMBUS_IT_NACKI NACK received interrupt enable SMBUS_IT_ADDRI Address match interrupt enable SMBUS_IT_RXI RX interrupt enable SMBUS_IT_TXI TX interrupt enable

Return values:

None

Definition at line 447 of file stm32l4xx_hal_smbus.h.

Referenced by SMBUS_Enable_IRQ().

#define __HAL_SMBUS_GENERATE_NACK

(

__HANDLE__

)

(SET_BIT((__HANDLE__)->Instance->CR2, I2C_CR2_NACK))

Generate a Non-Acknowledge SMBUS peripheral in Slave mode.

Parameters:

__HANDLE__

specifies the SMBUS Handle.

Return values:

None

Definition at line 547 of file stm32l4xx_hal_smbus.h.

#define __HAL_SMBUS_GET_FLAG	(		__HANDLE__,
			__FLAG__
	)

Value:

(((((__HANDLE__)->Instance->ISR) & ((__FLAG__) & SMBUS_FLAG_MASK)) == \
    ((__FLAG__) & SMBUS_FLAG_MASK)) ? SET : RESET)

Definition at line 506 of file stm32l4xx_hal_smbus.h.

Referenced by HAL_SMBUS_IsDeviceReady(), SMBUS_Flush_TXDR(), SMBUS_Slave_ISR(), and SMBUS_WaitOnFlagUntilTimeout().

#define __HAL_SMBUS_GET_IT_SOURCE	(		__HANDLE__,
			__INTERRUPT__
	)		((((__HANDLE__)->Instance->CR1 & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)

Check whether the specified SMBUS interrupt source is enabled or not.

Parameters:

__HANDLE__	specifies the SMBUS Handle.
__INTERRUPT__	specifies the SMBUS interrupt source to check. This parameter can be one of the following values: SMBUS_IT_ERRI Errors interrupt enable SMBUS_IT_TCI Transfer complete interrupt enable SMBUS_IT_STOPI STOP detection interrupt enable SMBUS_IT_NACKI NACK received interrupt enable SMBUS_IT_ADDRI Address match interrupt enable SMBUS_IT_RXI RX interrupt enable SMBUS_IT_TXI TX interrupt enable

Return values:

The	new state of __IT__ (SET or RESET).

Definition at line 479 of file stm32l4xx_hal_smbus.h.

#define __HAL_SMBUS_RESET_HANDLE_STATE

(

__HANDLE__

)

Value:

do{                                               \
                                                                 (__HANDLE__)->State = HAL_SMBUS_STATE_RESET;  \
                                                                 (__HANDLE__)->MspInitCallback = NULL;            \
                                                                 (__HANDLE__)->MspDeInitCallback = NULL;          \
                                                               } while(0)

Reset SMBUS handle state.

Parameters:

__HANDLE__

specifies the SMBUS Handle.

Return values:

None

Definition at line 424 of file stm32l4xx_hal_smbus.h.

#define SMBUS_FLAG_MASK   (0x0001FFFFU)

Check whether the specified SMBUS flag is set or not.

Parameters:

__HANDLE__

specifies the SMBUS Handle.

__FLAG__

specifies the flag to check. This parameter can be one of the following values: SMBUS_FLAG_TXE Transmit data register empty SMBUS_FLAG_TXIS Transmit interrupt status SMBUS_FLAG_RXNE Receive data register not empty SMBUS_FLAG_ADDR Address matched (slave mode) SMBUS_FLAG_AF NACK received flag SMBUS_FLAG_STOPF STOP detection flag SMBUS_FLAG_TC Transfer complete (master mode) SMBUS_FLAG_TCR Transfer complete reload SMBUS_FLAG_BERR Bus error SMBUS_FLAG_ARLO Arbitration lost SMBUS_FLAG_OVR Overrun/Underrun SMBUS_FLAG_PECERR PEC error in reception SMBUS_FLAG_TIMEOUT Timeout or Tlow detection flag SMBUS_FLAG_ALERT SMBus alert SMBUS_FLAG_BUSY Bus busy SMBUS_FLAG_DIR Transfer direction (slave mode)

Return values:

The	new state of __FLAG__ (SET or RESET).

Definition at line 505 of file stm32l4xx_hal_smbus.h.