Defines
#define	__HAL_QSPI_RESET_HANDLE_STATE(__HANDLE__)
	Reset QSPI handle state.
#define	__HAL_QSPI_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN)
	Enable the QSPI peripheral.
#define	__HAL_QSPI_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN)
	Disable the QSPI peripheral.
#define	__HAL_QSPI_ENABLE_IT(__HANDLE__, __INTERRUPT__) SET_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))
	Enable the specified QSPI interrupt.
#define	__HAL_QSPI_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))
	Disable the specified QSPI interrupt.
#define	__HAL_QSPI_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (READ_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) == (__INTERRUPT__))
	Check whether the specified QSPI interrupt source is enabled or not.
#define	__HAL_QSPI_GET_FLAG(__HANDLE__, __FLAG__) ((READ_BIT((__HANDLE__)->Instance->SR, (__FLAG__)) != 0U) ? SET : RESET)
	Check whether the selected QSPI flag is set or not.
#define	__HAL_QSPI_CLEAR_FLAG(__HANDLE__, __FLAG__) WRITE_REG((__HANDLE__)->Instance->FCR, (__FLAG__))
	Clears the specified QSPI's flag status.

Define Documentation

#define __HAL_QSPI_CLEAR_FLAG	(	__HANDLE__,
		__FLAG__
	)	WRITE_REG((__HANDLE__)->Instance->FCR, (__FLAG__))

Clears the specified QSPI's flag status.

Parameters:

__HANDLE__	specifies the QSPI Handle.
__FLAG__	specifies the QSPI clear register flag that needs to be set This parameter can be one of the following values: QSPI_FLAG_TO: QSPI Timeout flag QSPI_FLAG_SM: QSPI Status match flag QSPI_FLAG_TC: QSPI Transfer complete flag QSPI_FLAG_TE: QSPI Transfer error flag

Return values:

None

Definition at line 556 of file stm32l4xx_hal_qspi.h.

Referenced by HAL_QSPI_Abort(), HAL_QSPI_Abort_IT(), HAL_QSPI_AutoPolling(), HAL_QSPI_AutoPolling_IT(), HAL_QSPI_Command(), HAL_QSPI_Command_IT(), HAL_QSPI_MemoryMapped(), HAL_QSPI_Receive(), HAL_QSPI_Receive_DMA(), HAL_QSPI_Receive_IT(), HAL_QSPI_Transmit(), HAL_QSPI_Transmit_DMA(), HAL_QSPI_Transmit_IT(), and QSPI_DMAAbortCplt().

#define __HAL_QSPI_DISABLE ( __HANDLE__ ) CLEAR_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN)

Disable the QSPI peripheral.

Parameters:

__HANDLE__ specifies the QSPI Handle.

Return values:

None

Definition at line 489 of file stm32l4xx_hal_qspi.h.

Referenced by HAL_QSPI_DeInit().

#define __HAL_QSPI_DISABLE_IT	(	__HANDLE__,
		__INTERRUPT__
	)	CLEAR_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))

Disable the specified QSPI interrupt.

Parameters:

__HANDLE__	specifies the QSPI Handle.
__INTERRUPT__	specifies the QSPI interrupt source to disable. This parameter can be one of the following values: QSPI_IT_TO: QSPI Timeout interrupt QSPI_IT_SM: QSPI Status match interrupt QSPI_IT_FT: QSPI FIFO threshold interrupt QSPI_IT_TC: QSPI Transfer complete interrupt QSPI_IT_TE: QSPI Transfer error interrupt

Return values:

None

Definition at line 516 of file stm32l4xx_hal_qspi.h.

Referenced by HAL_QSPI_Abort_IT(), and HAL_QSPI_IRQHandler().

#define __HAL_QSPI_ENABLE ( __HANDLE__ ) SET_BIT((__HANDLE__)->Instance->CR, QUADSPI_CR_EN)

Enable the QSPI peripheral.

Parameters:

__HANDLE__ specifies the QSPI Handle.

Return values:

None

Definition at line 483 of file stm32l4xx_hal_qspi.h.

Referenced by HAL_QSPI_Init().

#define __HAL_QSPI_ENABLE_IT	(	__HANDLE__,
		__INTERRUPT__
	)	SET_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__))

Enable the specified QSPI interrupt.

Parameters:

__HANDLE__	specifies the QSPI Handle.
__INTERRUPT__	specifies the QSPI interrupt source to enable. This parameter can be one of the following values: QSPI_IT_TO: QSPI Timeout interrupt QSPI_IT_SM: QSPI Status match interrupt QSPI_IT_FT: QSPI FIFO threshold interrupt QSPI_IT_TC: QSPI Transfer complete interrupt QSPI_IT_TE: QSPI Transfer error interrupt

Return values:

None

Definition at line 502 of file stm32l4xx_hal_qspi.h.

Referenced by HAL_QSPI_Abort_IT(), HAL_QSPI_AutoPolling_IT(), HAL_QSPI_Command_IT(), HAL_QSPI_MemoryMapped(), HAL_QSPI_Receive_DMA(), HAL_QSPI_Receive_IT(), HAL_QSPI_Transmit_DMA(), HAL_QSPI_Transmit_IT(), QSPI_DMAAbortCplt(), QSPI_DMARxCplt(), and QSPI_DMATxCplt().

#define __HAL_QSPI_GET_FLAG	(	__HANDLE__,
		__FLAG__
	)	((READ_BIT((__HANDLE__)->Instance->SR, (__FLAG__)) != 0U) ? SET : RESET)

Check whether the selected QSPI flag is set or not.

Parameters:

__HANDLE__	specifies the QSPI Handle.
__FLAG__	specifies the QSPI flag to check. This parameter can be one of the following values: QSPI_FLAG_BUSY: QSPI Busy flag QSPI_FLAG_TO: QSPI Timeout flag QSPI_FLAG_SM: QSPI Status match flag QSPI_FLAG_FT: QSPI FIFO threshold flag QSPI_FLAG_TC: QSPI Transfer complete flag QSPI_FLAG_TE: QSPI Transfer error flag

Return values:

None

Definition at line 544 of file stm32l4xx_hal_qspi.h.

Referenced by HAL_QSPI_IRQHandler(), and QSPI_WaitFlagStateUntilTimeout().

#define __HAL_QSPI_GET_IT_SOURCE	(	__HANDLE__,
		__INTERRUPT__
	)	(READ_BIT((__HANDLE__)->Instance->CR, (__INTERRUPT__)) == (__INTERRUPT__))

Check whether the specified QSPI interrupt source is enabled or not.

Parameters:

__HANDLE__	specifies the QSPI Handle.
__INTERRUPT__	specifies the QSPI interrupt source to check. This parameter can be one of the following values: QSPI_IT_TO: QSPI Timeout interrupt QSPI_IT_SM: QSPI Status match interrupt QSPI_IT_FT: QSPI FIFO threshold interrupt QSPI_IT_TC: QSPI Transfer complete interrupt QSPI_IT_TE: QSPI Transfer error interrupt

Return values:

The	new state of __INTERRUPT__ (TRUE or FALSE).

Definition at line 529 of file stm32l4xx_hal_qspi.h.

#define __HAL_QSPI_RESET_HANDLE_STATE ( __HANDLE__ )

Value:

do {                                              \
                                                                  (__HANDLE__)->State = HAL_QSPI_STATE_RESET; \
                                                                  (__HANDLE__)->MspInitCallback = NULL;       \
                                                                  (__HANDLE__)->MspDeInitCallback = NULL;     \
                                                               } while(0)

Reset QSPI handle state.

Parameters:

__HANDLE__ QSPI handle.

Return values:

None

Definition at line 470 of file stm32l4xx_hal_qspi.h.

Defines

Define Documentation