Defines
#define	__HAL_UART_RESET_HANDLE_STATE(__HANDLE__)
	Reset UART handle states.
#define	__HAL_UART_FLUSH_DRREGISTER(__HANDLE__)
	Flush the UART Data registers.
#define	__HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__))
	Clear the specified UART pending flag.
#define	__HAL_UART_CLEAR_PEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_PEF)
	Clear the UART PE pending flag.
#define	__HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_FEF)
	Clear the UART FE pending flag.
#define	__HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_NEF)
	Clear the UART NE pending flag.
#define	__HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_OREF)
	Clear the UART ORE pending flag.
#define	__HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_IDLEF)
	Clear the UART IDLE pending flag.
#define	__HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
	Check whether the specified UART flag is set or not.
#define	__HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__)
	Enable the specified UART interrupt.
#define	__HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__)
	Disable the specified UART interrupt.
#define	__HAL_UART_GET_IT(__HANDLE__, __INTERRUPT__)
	Check whether the specified UART interrupt has occurred or not.
#define	__HAL_UART_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)
	Check whether the specified UART interrupt source is enabled or not.
#define	__HAL_UART_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
	Clear the specified UART ISR flag, in setting the proper ICR register flag.
#define	__HAL_UART_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR \|= (uint16_t)(__REQ__))
	Set a specific UART request flag.
#define	__HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3\|= USART_CR3_ONEBIT)
	Enable the UART one bit sample method.
#define	__HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= ~USART_CR3_ONEBIT)
	Disable the UART one bit sample method.
#define	__HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 \|= USART_CR1_UE)
	Enable UART.
#define	__HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
	Disable UART.
#define	__HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__)
	Enable CTS flow control.
#define	__HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__)
	Disable CTS flow control.
#define	__HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__)
	Enable RTS flow control.
#define	__HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__)
	Disable RTS flow control.

Define Documentation

#define __HAL_UART_CLEAR_FEFLAG ( __HANDLE__ ) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_FEF)

Clear the UART FE pending flag.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 916 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_CLEAR_FLAG	(	__HANDLE__,
		__FLAG__
	)	((__HANDLE__)->Instance->ICR = (__FLAG__))

Clear the specified UART pending flag.

Parameters:

__HANDLE__ specifies the UART Handle.

__FLAG__

specifies the flag to check. This parameter can be any combination of the following values:

UART_CLEAR_PEF Parity Error Clear Flag
UART_CLEAR_FEF Framing Error Clear Flag
UART_CLEAR_NEF Noise detected Clear Flag
UART_CLEAR_OREF Overrun Error Clear Flag
UART_CLEAR_IDLEF IDLE line detected Clear Flag
UART_CLEAR_TXFECF TXFIFO empty clear Flag
UART_CLEAR_TCF Transmission Complete Clear Flag
UART_CLEAR_RTOF Receiver Timeout clear flag
UART_CLEAR_LBDF LIN Break Detection Clear Flag
UART_CLEAR_CTSF CTS Interrupt Clear Flag
UART_CLEAR_CMF Character Match Clear Flag
UART_CLEAR_WUF Wake Up from stop mode Clear Flag

Return values:

None

Definition at line 904 of file stm32l4xx_hal_uart.h.

Referenced by HAL_UART_Abort(), HAL_UART_Abort_IT(), HAL_UART_AbortReceive(), HAL_UART_AbortReceive_IT(), HAL_UART_DMAResume(), HAL_UART_IRQHandler(), HAL_UART_Transmit_DMA(), HAL_UARTEx_ReceiveToIdle(), HAL_UARTEx_ReceiveToIdle_DMA(), HAL_UARTEx_ReceiveToIdle_IT(), UART_DMARxAbortCallback(), UART_DMARxOnlyAbortCallback(), UART_DMATxAbortCallback(), UART_RxISR_16BIT(), UART_RxISR_8BIT(), and UART_WaitOnFlagUntilTimeout().

#define __HAL_UART_CLEAR_IDLEFLAG ( __HANDLE__ ) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_IDLEF)

Clear the UART IDLE pending flag.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 934 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_CLEAR_IT	(	__HANDLE__,
		__IT_CLEAR__
	)	((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))

Clear the specified UART ISR flag, in setting the proper ICR register flag.

Parameters:

__HANDLE__ specifies the UART Handle.

__IT_CLEAR__

specifies the interrupt clear register flag that needs to be set to clear the corresponding interrupt This parameter can be one of the following values:

UART_CLEAR_PEF Parity Error Clear Flag
UART_CLEAR_FEF Framing Error Clear Flag
UART_CLEAR_NEF Noise detected Clear Flag
UART_CLEAR_OREF Overrun Error Clear Flag
UART_CLEAR_IDLEF IDLE line detected Clear Flag
UART_CLEAR_RTOF Receiver timeout clear flag
UART_CLEAR_TXFECF TXFIFO empty Clear Flag
UART_CLEAR_TCF Transmission Complete Clear Flag
UART_CLEAR_LBDF LIN Break Detection Clear Flag
UART_CLEAR_CTSF CTS Interrupt Clear Flag
UART_CLEAR_CMF Character Match Clear Flag
UART_CLEAR_WUF Wake Up from stop mode Clear Flag

Return values:

None

Definition at line 1120 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_CLEAR_NEFLAG ( __HANDLE__ ) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_NEF)

Clear the UART NE pending flag.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 922 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_CLEAR_OREFLAG ( __HANDLE__ ) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_OREF)

Clear the UART ORE pending flag.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 928 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_CLEAR_PEFLAG ( __HANDLE__ ) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_PEF)

Clear the UART PE pending flag.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 910 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_DISABLE ( __HANDLE__ ) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)

Disable UART.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1157 of file stm32l4xx_hal_uart.h.

Referenced by HAL_HalfDuplex_Init(), HAL_LIN_Init(), HAL_MultiProcessor_Init(), HAL_MultiProcessorEx_AddressLength_Set(), HAL_RS485Ex_Init(), HAL_UART_DeInit(), HAL_UART_Init(), and HAL_UARTEx_StopModeWakeUpSourceConfig().

#define __HAL_UART_DISABLE_IT	(	__HANDLE__,
		__INTERRUPT__
	)

Value:

(\
                                                           ((((uint8_t)(__INTERRUPT__)) >> 5U) == 1U)?\
                                                           ((__HANDLE__)->Instance->CR1 &= ~ (1U <<\
                                                               ((__INTERRUPT__) & UART_IT_MASK))): \
                                                           ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2U)?\
                                                           ((__HANDLE__)->Instance->CR2 &= ~ (1U <<\
                                                               ((__INTERRUPT__) & UART_IT_MASK))): \
                                                           ((__HANDLE__)->Instance->CR3 &= ~ (1U <<\
                                                               ((__INTERRUPT__) & UART_IT_MASK))))

Disable the specified UART interrupt.

Parameters:

__HANDLE__ specifies the UART Handle.

__INTERRUPT__

specifies the UART interrupt source to disable. This parameter can be one of the following values:

UART_IT_RXFF RXFIFO Full interrupt
UART_IT_TXFE TXFIFO Empty interrupt
UART_IT_RXFT RXFIFO threshold interrupt
UART_IT_TXFT TXFIFO threshold interrupt
UART_IT_WUF Wakeup from stop mode interrupt
UART_IT_CM Character match interrupt
UART_IT_CTS CTS change interrupt
UART_IT_LBD LIN Break detection interrupt
UART_IT_TXE Transmit Data Register empty interrupt
UART_IT_TXFNF TX FIFO not full interrupt
UART_IT_TC Transmission complete interrupt
UART_IT_RXNE Receive Data register not empty interrupt
UART_IT_RXFNE RXFIFO not empty interrupt
UART_IT_RTO Receive Timeout interrupt
UART_IT_IDLE Idle line detection interrupt
UART_IT_PE Parity Error interrupt
UART_IT_ERR Error interrupt (Frame error, noise error, overrun error)

Return values:

None

Definition at line 1034 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_ENABLE ( __HANDLE__ ) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)

Enable UART.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1151 of file stm32l4xx_hal_uart.h.

Referenced by HAL_HalfDuplex_Init(), HAL_LIN_Init(), HAL_MultiProcessor_Init(), HAL_MultiProcessorEx_AddressLength_Set(), HAL_RS485Ex_Init(), HAL_UART_Init(), and HAL_UARTEx_StopModeWakeUpSourceConfig().

#define __HAL_UART_ENABLE_IT	(	__HANDLE__,
		__INTERRUPT__
	)

Value:

(\
                                                           ((((uint8_t)(__INTERRUPT__)) >> 5U) == 1U)?\
                                                           ((__HANDLE__)->Instance->CR1 |= (1U <<\
                                                               ((__INTERRUPT__) & UART_IT_MASK))): \
                                                           ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2U)?\
                                                           ((__HANDLE__)->Instance->CR2 |= (1U <<\
                                                               ((__INTERRUPT__) & UART_IT_MASK))): \
                                                           ((__HANDLE__)->Instance->CR3 |= (1U <<\
                                                               ((__INTERRUPT__) & UART_IT_MASK))))

Enable the specified UART interrupt.

Parameters:

__HANDLE__ specifies the UART Handle.

__INTERRUPT__

specifies the UART interrupt source to enable. This parameter can be one of the following values:

UART_IT_RXFF RXFIFO Full interrupt
UART_IT_TXFE TXFIFO Empty interrupt
UART_IT_RXFT RXFIFO threshold interrupt
UART_IT_TXFT TXFIFO threshold interrupt
UART_IT_WUF Wakeup from stop mode interrupt
UART_IT_CM Character match interrupt
UART_IT_CTS CTS change interrupt
UART_IT_LBD LIN Break detection interrupt
UART_IT_TXE Transmit Data Register empty interrupt
UART_IT_TXFNF TX FIFO not full interrupt
UART_IT_TC Transmission complete interrupt
UART_IT_RXNE Receive Data register not empty interrupt
UART_IT_RXFNE RXFIFO not empty interrupt
UART_IT_RTO Receive Timeout interrupt
UART_IT_IDLE Idle line detection interrupt
UART_IT_PE Parity Error interrupt
UART_IT_ERR Error interrupt (frame error, noise error, overrun error)

Return values:

None

Definition at line 1001 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_FLUSH_DRREGISTER ( __HANDLE__ )

Value:

do{                \
    SET_BIT((__HANDLE__)->Instance->RQR, UART_RXDATA_FLUSH_REQUEST); \
    SET_BIT((__HANDLE__)->Instance->RQR, UART_TXDATA_FLUSH_REQUEST); \
  }  while(0U)

Flush the UART Data registers.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 880 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_GET_FLAG	(	__HANDLE__,
		__FLAG__
	)	(((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))

Check whether the specified UART flag is set or not.

Parameters:

__HANDLE__ specifies the UART Handle.

__FLAG__

specifies the flag to check. This parameter can be one of the following values:

UART_FLAG_TXFT TXFIFO threshold flag
UART_FLAG_RXFT RXFIFO threshold flag
UART_FLAG_RXFF RXFIFO Full flag
UART_FLAG_TXFE TXFIFO Empty flag
UART_FLAG_REACK Receive enable acknowledge flag
UART_FLAG_TEACK Transmit enable acknowledge flag
UART_FLAG_WUF Wake up from stop mode flag
UART_FLAG_RWU Receiver wake up flag (if the UART in mute mode)
UART_FLAG_SBKF Send Break flag
UART_FLAG_CMF Character match flag
UART_FLAG_BUSY Busy flag
UART_FLAG_ABRF Auto Baud rate detection flag
UART_FLAG_ABRE Auto Baud rate detection error flag
UART_FLAG_CTS CTS Change flag
UART_FLAG_LBDF LIN Break detection flag
UART_FLAG_TXE Transmit data register empty flag
UART_FLAG_TXFNF UART TXFIFO not full flag
UART_FLAG_TC Transmission Complete flag
UART_FLAG_RXNE Receive data register not empty flag
UART_FLAG_RXFNE UART RXFIFO not empty flag
UART_FLAG_RTOF Receiver Timeout flag
UART_FLAG_IDLE Idle Line detection flag
UART_FLAG_ORE Overrun Error flag
UART_FLAG_NE Noise Error flag
UART_FLAG_FE Framing Error flag
UART_FLAG_PE Parity Error flag

Return values:

The	new state of __FLAG__ (TRUE or FALSE).

Definition at line 976 of file stm32l4xx_hal_uart.h.

Referenced by HAL_UARTEx_ReceiveToIdle(), UART_RxISR_16BIT(), UART_RxISR_8BIT(), and UART_WaitOnFlagUntilTimeout().

#define __HAL_UART_GET_IT	(	__HANDLE__,
		__INTERRUPT__
	)

Value:

((((__HANDLE__)->Instance->ISR\
                                                        & (1U << ((__INTERRUPT__)>> 8U))) != RESET) ? SET : RESET)

Check whether the specified UART interrupt has occurred or not.

Parameters:

__HANDLE__ specifies the UART Handle.

__INTERRUPT__

specifies the UART interrupt to check. This parameter can be one of the following values:

UART_IT_RXFF RXFIFO Full interrupt
UART_IT_TXFE TXFIFO Empty interrupt
UART_IT_RXFT RXFIFO threshold interrupt
UART_IT_TXFT TXFIFO threshold interrupt
UART_IT_WUF Wakeup from stop mode interrupt
UART_IT_CM Character match interrupt
UART_IT_CTS CTS change interrupt
UART_IT_LBD LIN Break detection interrupt
UART_IT_TXE Transmit Data Register empty interrupt
UART_IT_TXFNF TX FIFO not full interrupt
UART_IT_TC Transmission complete interrupt
UART_IT_RXNE Receive Data register not empty interrupt
UART_IT_RXFNE RXFIFO not empty interrupt
UART_IT_RTO Receive Timeout interrupt
UART_IT_IDLE Idle line detection interrupt
UART_IT_PE Parity Error interrupt
UART_IT_ERR Error interrupt (Frame error, noise error, overrun error)

Return values:

The	new state of __INTERRUPT__ (SET or RESET).

Definition at line 1067 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_GET_IT_SOURCE	(	__HANDLE__,
		__INTERRUPT__
	)

Value:

((((((((uint8_t)(__INTERRUPT__)) >> 5U) == 1U) ?\
                                                                (__HANDLE__)->Instance->CR1 : \
                                                                (((((uint8_t)(__INTERRUPT__)) >> 5U) == 2U) ?\
                                                                 (__HANDLE__)->Instance->CR2 : \
                                                                 (__HANDLE__)->Instance->CR3)) & (1U <<\
                                                                     (((uint16_t)(__INTERRUPT__)) &\
                                                                      UART_IT_MASK)))  != RESET) ? SET : RESET)

Check whether the specified UART interrupt source is enabled or not.

Parameters:

__HANDLE__ specifies the UART Handle.

__INTERRUPT__

specifies the UART interrupt source to check. This parameter can be one of the following values:

UART_IT_RXFF RXFIFO Full interrupt
UART_IT_TXFE TXFIFO Empty interrupt
UART_IT_RXFT RXFIFO threshold interrupt
UART_IT_TXFT TXFIFO threshold interrupt
UART_IT_WUF Wakeup from stop mode interrupt
UART_IT_CM Character match interrupt
UART_IT_CTS CTS change interrupt
UART_IT_LBD LIN Break detection interrupt
UART_IT_TXE Transmit Data Register empty interrupt
UART_IT_TXFNF TX FIFO not full interrupt
UART_IT_TC Transmission complete interrupt
UART_IT_RXNE Receive Data register not empty interrupt
UART_IT_RXFNE RXFIFO not empty interrupt
UART_IT_RTO Receive Timeout interrupt
UART_IT_IDLE Idle line detection interrupt
UART_IT_PE Parity Error interrupt
UART_IT_ERR Error interrupt (Frame error, noise error, overrun error)

Return values:

The	new state of __INTERRUPT__ (SET or RESET).

Definition at line 1093 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_HWCONTROL_CTS_DISABLE ( __HANDLE__ )

Value:

do{                                                              \
    ATOMIC_CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
    (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE);             \
  } while(0U)

Disable CTS flow control.

Note:

This macro allows to disable CTS hardware flow control for a given UART instance, without need to call HAL_UART_Init() function. As involving direct access to UART registers, usage of this macro should be fully endorsed by user.

As macro is expected to be used for modifying CTS Hw flow control feature activation, without need for USART instance Deinit/Init, following conditions for macro call should be fulfilled :

UART instance should have already been initialised (through call of HAL_UART_Init() )
macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1191 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_HWCONTROL_CTS_ENABLE ( __HANDLE__ )

Value:

do{                                                             \
    ATOMIC_SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE);  \
    (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE;               \
  } while(0U)

Enable CTS flow control.

Note:

This macro allows to enable CTS hardware flow control for a given UART instance, without need to call HAL_UART_Init() function. As involving direct access to UART registers, usage of this macro should be fully endorsed by user.

As macro is expected to be used for modifying CTS Hw flow control feature activation, without need for USART instance Deinit/Init, following conditions for macro call should be fulfilled :

UART instance should have already been initialised (through call of HAL_UART_Init() )
macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1172 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_HWCONTROL_RTS_DISABLE ( __HANDLE__ )

Value:

do{                                                             \
    ATOMIC_CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\
    (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE);            \
  } while(0U)

Disable RTS flow control.

Note:

This macro allows to disable RTS hardware flow control for a given UART instance, without need to call HAL_UART_Init() function. As involving direct access to UART registers, usage of this macro should be fully endorsed by user.

As macro is expected to be used for modifying RTS Hw flow control feature activation, without need for USART instance Deinit/Init, following conditions for macro call should be fulfilled :

UART instance should have already been initialised (through call of HAL_UART_Init() )
macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1229 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_HWCONTROL_RTS_ENABLE ( __HANDLE__ )

Value:

do{                                                            \
    ATOMIC_SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \
    (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE;              \
  } while(0U)

Enable RTS flow control.

Note:

This macro allows to enable RTS hardware flow control for a given UART instance, without need to call HAL_UART_Init() function. As involving direct access to UART registers, usage of this macro should be fully endorsed by user.

As macro is expected to be used for modifying RTS Hw flow control feature activation, without need for USART instance Deinit/Init, following conditions for macro call should be fulfilled :

UART instance should have already been initialised (through call of HAL_UART_Init() )
macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__)) and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1210 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_ONE_BIT_SAMPLE_DISABLE ( __HANDLE__ ) ((__HANDLE__)->Instance->CR3 &= ~USART_CR3_ONEBIT)

Disable the UART one bit sample method.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1145 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_ONE_BIT_SAMPLE_ENABLE ( __HANDLE__ ) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)

Enable the UART one bit sample method.

Parameters:

__HANDLE__ specifies the UART Handle.

Return values:

None

Definition at line 1139 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_RESET_HANDLE_STATE ( __HANDLE__ )

Value:

do{                                                   \
                                                       (__HANDLE__)->gState = HAL_UART_STATE_RESET;      \
                                                       (__HANDLE__)->RxState = HAL_UART_STATE_RESET;     \
                                                       (__HANDLE__)->MspInitCallback = NULL;             \
                                                       (__HANDLE__)->MspDeInitCallback = NULL;           \
                                                     } while(0U)

Reset UART handle states.

Parameters:

__HANDLE__ UART handle.

Return values:

None

Definition at line 863 of file stm32l4xx_hal_uart.h.

#define __HAL_UART_SEND_REQ	(	__HANDLE__,
		__REQ__
	)	((__HANDLE__)->Instance->RQR \|= (uint16_t)(__REQ__))

Set a specific UART request flag.

Parameters:

__HANDLE__	specifies the UART Handle.
__REQ__	specifies the request flag to set This parameter can be one of the following values: UART_AUTOBAUD_REQUEST Auto-Baud Rate Request UART_SENDBREAK_REQUEST Send Break Request UART_MUTE_MODE_REQUEST Mute Mode Request UART_RXDATA_FLUSH_REQUEST Receive Data flush Request UART_TXDATA_FLUSH_REQUEST Transmit data flush Request

Return values:

None

Definition at line 1133 of file stm32l4xx_hal_uart.h.

Referenced by HAL_LIN_SendBreak(), HAL_MultiProcessor_EnterMuteMode(), HAL_UART_Abort(), HAL_UART_Abort_IT(), HAL_UART_AbortReceive(), HAL_UART_AbortReceive_IT(), HAL_UART_AbortTransmit(), HAL_UART_AbortTransmit_IT(), UART_DMARxAbortCallback(), UART_DMARxOnlyAbortCallback(), UART_DMATxAbortCallback(), UART_DMATxOnlyAbortCallback(), UART_RxISR_16BIT(), and UART_RxISR_8BIT().

Defines

Define Documentation